docs - coneplot problems

load wind;

xmin = min(x(:));
xmax = max(x(:));
ymin = min(y(:));
ymax = max(y(:));
zmin = min(z(:));

xrange = linspace(xmin,xmax,8);
yrange = linspace(ymin,ymax,8);
zrange = 3:4:15;
[cx,cy,cz] = meshgrid(xrange,yrange,zrange);

figure;
hcone = coneplot(x,y,z,u,v,w,cx,cy,cz,5);

hcone.FaceColor = 'red';
hcone.EdgeColor = 'none';


fig2plotly(gcf, 'TreatAs', 'coneplot');

The red color is not properly translated to plotly plot

load wind;

xmin = min(x(:));
xmax = max(x(:));
ymin = min(y(:));
ymax = max(y(:));
zmin = min(z(:));

xrange = linspace(xmin,xmax,8);
yrange = linspace(ymin,ymax,8);
zrange = 3:4:15;
[cx,cy,cz] = meshgrid(xrange,yrange,zrange);

figure;
hcone = coneplot(x,y,z,u,v,w,cx,cy,cz,5);

hcone.FaceColor = 'red';
hcone.EdgeColor = 'none';

hold on;
wind_speed = sqrt(u.^2 + v.^2 + w.^2);

hsurfaces = slice(x,y,z,wind_speed,[xmin,xmax],ymax,zmin);
set(hsurfaces,'FaceColor','interp','EdgeColor','none');
hold off;

fig2plotly(gcf, 'TreatAs', 'coneplot');

The vector field added to background with wind_speed is not added to plotly plot

load wind;

xmin = min(x(:));
xmax = max(x(:));
ymin = min(y(:));
ymax = max(y(:));
zmin = min(z(:));

xrange = linspace(xmin,xmax,8);
yrange = linspace(ymin,ymax,8);
zrange = 3:4:15;
[cx,cy,cz] = meshgrid(xrange,yrange,zrange);

figure;
hcone = coneplot(x,y,z,u,v,w,cx,cy,cz,5);

hcone.FaceColor = 'red';
hcone.EdgeColor = 'none';

hold on;
wind_speed = sqrt(u.^2 + v.^2 + w.^2);

hsurfaces = slice(x,y,z,wind_speed,[xmin,xmax],ymax,zmin);
set(hsurfaces,'FaceColor','interp','EdgeColor','none');
hold off;

camlight right;
lighting gouraud;
set(hsurfaces,'AmbientStrength',0.6);
hcone.DiffuseStrength = 0.8;

fig2plotly(gcf, 'TreatAs', 'coneplot')

The light source lighting gouraud; is not added to plotly plot.

load wind;

xmin = min(x(:));
xmax = max(x(:));
ymin = min(y(:));
ymax = max(y(:));
zmin = min(z(:));

xrange = linspace(xmin,xmax,8);
yrange = linspace(ymin,ymax,8);
zrange = 3:4:15;
[cx,cy,cz] = meshgrid(xrange,yrange,zrange);

figure;
hcone = coneplot(x,y,z,u,v,w,cx,cy,cz,5);

hcone.FaceColor = 'red';
hcone.EdgeColor = 'none';

hold on;
wind_speed = sqrt(u.^2 + v.^2 + w.^2);

hsurfaces = slice(x,y,z,wind_speed,[xmin,xmax],ymax,zmin);
set(hsurfaces,'FaceColor','interp','EdgeColor','none');
hold off;

camlight right;
lighting gouraud;
set(hsurfaces,'AmbientStrength',0.6);
hcone.DiffuseStrength = 0.8;

view(30,40)
daspect([2,2,1])

fig2plotly(gcf, 'TreatAs', 'coneplot')

view(30,40)
daspect([2,2,1])

is supposed to change initial view angle, and aspect ratio of the plot. Does not do it

提供された MATLAB の例を、TreatAs を coneplot に設定して fig2plotly で実行します。cone の FaceColor と EdgeColor、slice の背景、lighting の設定、および view/daspect の変更について出力を比較します。これらの coneplot、surface、lighting、camera、aspect-ratio の設定が Plotly の結果に反映されれば完了です。