Dubious code in printFloat(double number, uint8_t digits)

A function named printFloat that prints a double is unfortunate naming!

https://github.com/arduino/ArduinoCore-avr/blob/2ff00ae7d4e85fa422b7918ee12baf56a1f3006e/cores/arduino/Print.cpp#L229

The comment indicates a problem. It works but empirical constants are not good practice!

The range check is needed in order to prevent the integer part of the float overflowing in
https://github.com/arduino/ArduinoCore-avr/blob/2ff00ae7d4e85fa422b7918ee12baf56a1f3006e/cores/arduino/Print.cpp#L247
unsigned long is not necessarily 32 bits so the numeric literal is non-portable.
The constant is actually the unsigned long equivalent of INT_MAX - 1. (The -1 is to allow for rounding but further thought needed to be certain of that).

I have a fix which avoids the need for int_part so the problem no longer arises. It also makes the implementation of %g and %e formats relatively trivial.

* Some testing but far from thorough.
* Uses sig figs for %f format instead of decimal places but that can be changed.
* Precision as a parameter not implemented.
* Consideration should be given to ```printFloat(float f, struct PrintOptions *options)```
* It prints a float but that is more than adequate for most purposes.

I would welcome feedback on the various options before I do anything further.

```
#define F_LARGE 6 /* maximum exponent for F format */
#define F_SMALL -3 /* minimum exponent for F format */
#define E_SIG_FIG 4 /* significant figures for E format */
#define F_SIG_FIG 6

// Buffer size. The +1 allows for the rounding digit.
#if E_SIG_FIG > F_SIG_FIG
#define SIZE (E_SIG_FIG + 1)
#else
#define SIZE (F_SIG_FIG + 1)
#endif

void printFloat(float f) {
int8_t d;
char buffer[SIZE];
bool negative;
bool Eformat = false;
uint8_t start = 1; // index of first digit leaving room for a carry from the rounding
uint8_t dp; // index of first digit after the decimal point
uint8_t finish; // index of extra digit used for rounding
int8_t i; // loop counter (must be signed)

if (isnan(f)) { print("nan"); return; }
if (isinf(f)) { print("inf"); return; }

negative = f < 0.0;
if (negative) { f = -f; print('-'); }

int8_t exponent = 0;
while (f >= 10.0) { exponent++; f /= 10.0; }
while (f < 1.0) { exponent--; f *= 10.0; }

// need one more digit for use when rounding
if (exponent > F_LARGE || exponent < F_SMALL) {
// E format
finish = start + E_SIG_FIG;
dp = 1;
Eformat = true;
}
else {
// F format
finish = start + F_SIG_FIG;
dp = exponent + 1;
}

// store the digit chars into the buffer
for (uint8_t i = start; i <= finish; i++) {
d = (uint8_t)f;
buffer[i] = '0' + d;
f -= d;
// Could check for f==0 here and save some multiplies but larger code size
f *= 10.;
}

// rounding
if (buffer[finish] >= '5') {
i = finish - 1;
buffer[0] = '0';
while (buffer[i] == '9') {
buffer[i] = '0';
i--;
}
buffer[i]++;
}

if (buffer[0] == '1') {
start = 0; // there was a carry from the rounding
}
else {
dp++;
}

if (exponent >= 0) { // positive exponent
for ( i = start; i < dp; i++) {
print(buffer[i]);
}
print('.');
for ( i = dp; i < finish; i++) {
print(buffer[i]);
}
}
else { // negative exponent
if (Eformat) {
print(buffer[start]);
print('.');
for ( i = dp; i < finish; i++) {
print(buffer[i]);
}
}
else { // F format
print("0.");
for (i = 1; i < -exponent; i++) {
print('0');
}
for (i = start; i < finish; i++) {
print(buffer[i]);
}
}
}

if (Eformat) {
print('E');
print(exponent);
}
}
```

首先检查 cores/arduino/Print.cpp，尤其是 printFloat 和相关的范围检查代码。在更改实现之前，明确所需的格式、精度参数、float 与 double 的行为差异，以及 %g 和 %e 是否属于范围。完成的要求是就这些选项达成一致，并进行超出所述有限测试的测试。

由索引模型根据 Issue 内容生成。